Up: Built Sources [Contents][Index]
Suppose that foo.c includes bindir.h, which is
installation-dependent and not distributed: it needs to be built. Here
bindir.h defines the preprocessor macro bindir to the
value of the make variable bindir (inherited from
configure).
We suggest several implementations below. It’s not meant to be an exhaustive listing of all ways to handle built sources, but it will give you a few ideas if you encounter this issue.
This first implementation will illustrate the bootstrap issue mentioned in the previous section (see Built Sources).
Here is a tentative Makefile.am.
# This won't work.
bin_PROGRAMS = foo
foo_SOURCES = foo.c
nodist_foo_SOURCES = bindir.h
CLEANFILES = bindir.h
bindir.h: Makefile
echo '#define bindir "$(bindir)"' >$@
This setup doesn’t work, because Automake doesn’t know that foo.c includes bindir.h. Remember, automatic dependency tracking works as a side-effect of compilation, so the dependencies of foo.o will be known only after foo.o has been compiled (see Automatic dependency tracking). The symptom is as follows.
% make source='foo.c' object='foo.o' libtool=no \ depfile='.deps/foo.Po' tmpdepfile='.deps/foo.TPo' \ depmode=gcc /bin/sh ./depcomp \ gcc -I. -I. -g -O2 -c `test -f 'foo.c' || echo './'`foo.c foo.c:2: bindir.h: No such file or directory make: *** [foo.o] Error 1
In this example bindir.h is not distributed nor installed, and
it is not even being built on-time. One may wonder if the
‘nodist_foo_SOURCES = bindir.h’ line has any use at all. This
line simply states that bindir.h is a source of foo, so
for instance, it should be inspected while generating tags
(see Interfacing to etags). In other words, it does not help our present problem,
and the build would fail identically without it.
BUILT_SOURCESA solution is to require bindir.h to be built before anything
else. This is what BUILT_SOURCES is meant for (see Built Sources).
bin_PROGRAMS = foo
foo_SOURCES = foo.c
nodist_foo_SOURCES = bindir.h
BUILT_SOURCES = bindir.h
CLEANFILES = bindir.h
bindir.h: Makefile
echo '#define bindir "$(bindir)"' >$@
See how bindir.h gets built first:
% make echo '#define bindir "/usr/local/bin"' >bindir.h make all-am make[1]: Entering directory `/home/adl/tmp' source='foo.c' object='foo.o' libtool=no \ depfile='.deps/foo.Po' tmpdepfile='.deps/foo.TPo' \ depmode=gcc /bin/sh ./depcomp \ gcc -I. -I. -g -O2 -c `test -f 'foo.c' || echo './'`foo.c gcc -g -O2 -o foo foo.o make[1]: Leaving directory `/home/adl/tmp'
However, as said earlier, BUILT_SOURCES applies only to the
all, check, and install targets. It still fails
if you try to run ‘make foo’ explicitly:
% make clean test -z "bindir.h" || rm -f bindir.h test -z "foo" || rm -f foo rm -f *.o % : > .deps/foo.Po # Suppress previously recorded dependencies % make foo source='foo.c' object='foo.o' libtool=no \ depfile='.deps/foo.Po' tmpdepfile='.deps/foo.TPo' \ depmode=gcc /bin/sh ./depcomp \ gcc -I. -I. -g -O2 -c `test -f 'foo.c' || echo './'`foo.c foo.c:2: bindir.h: No such file or directory make: *** [foo.o] Error 1
Usually people are happy enough with BUILT_SOURCES because they
never build targets such as ‘make foo’ before ‘make all’, as
in the previous example. However if this matters to you, you can
avoid BUILT_SOURCES and record such dependencies explicitly in
the Makefile.am.
bin_PROGRAMS = foo
foo_SOURCES = foo.c
nodist_foo_SOURCES = bindir.h
foo.$(OBJEXT): bindir.h
CLEANFILES = bindir.h
bindir.h: Makefile
echo '#define bindir "$(bindir)"' >$@
You don’t have to list all the dependencies of foo.o explicitly, only those that might need to be built. If a dependency already exists, it will not hinder the first compilation and will be recorded by the normal dependency tracking code. (Note that after this first compilation the dependency tracking code will also have recorded the dependency between foo.o and bindir.h, so our explicit dependency is really useful to the first build only.)
Adding explicit dependencies like this can be a bit dangerous if you are not careful enough. This is due to the way Automake tries not to overwrite your rules (it assumes you know better than it). ‘foo.$(OBJEXT): bindir.h’ supersedes any rule Automake may want to output to build ‘foo.$(OBJEXT)’. It happens to work in this case because Automake doesn’t have to output any ‘foo.$(OBJEXT):’ target: it relies on a suffix rule instead (i.e., ‘.c.$(OBJEXT):’). Always check the generated Makefile.in if you do this.
It’s possible to define this preprocessor macro from configure,
either in config.h (see Defining
Directories in The Autoconf Manual), or by processing a
bindir.h.in file using AC_CONFIG_FILES
(see Configuration Actions in The
Autoconf Manual).
At this point it should be clear that building bindir.h from configure works well for this example. bindir.h will exist before you build any target, hence will not cause any dependency issue.
The Makefile can be shrunk as follows. We do not even have to mention bindir.h.
bin_PROGRAMS = foo foo_SOURCES = foo.c
However, it’s not always possible to build sources from configure, especially when these sources are generated by a tool that needs to be built first.
Another attractive idea is to define bindir as a variable or
function exported from bindir.o, and build bindir.c
instead of bindir.h.
noinst_PROGRAMS = foo
foo_SOURCES = foo.c bindir.h
nodist_foo_SOURCES = bindir.c
CLEANFILES = bindir.c
bindir.c: Makefile
echo 'const char bindir[] = "$(bindir)";' >$@
bindir.h contains just the variable’s declaration and doesn’t need to be built, so it won’t cause any trouble. bindir.o is always dependent on bindir.c, so bindir.c will get built first.
There is no panacea, of course. Each solution has its merits and drawbacks.
You cannot use BUILT_SOURCES if the ability to run ‘make
foo’ on a clean tree is important to you.
You won’t add explicit dependencies if you are leery of overriding an Automake rule by mistake.
Building files from ./configure is not always possible, neither is converting .h files into .c files.
Up: Built Sources [Contents][Index]